Toshiba Error Code 16, Compressor Position Circuit Fault
Toshiba error code 16 relates to how the outdoor board keeps track of the compressor motor while it spins. An inverter compressor needs precise timing, and that timing depends on knowing where the rotor sits. When the board loses that information, it stops and reports 16. Here we explain the code, the likely causes and what our technicians do about it.
What does Toshiba error code 16 mean?
In the Toshiba RAS check code table, 16 is the compressor position circuit. The outdoor inverter drives a brushless DC compressor motor, and to energise the right windings at the right moment, it must know the position of the rotor inside. On most Toshiba splits, the board works this out by reading electrical signals that the spinning motor feeds back through its own windings.
If those signals are missing, distorted or inconsistent, the board cannot time the drive properly. Rather than risk jerky running or damage, it shuts the compressor down and records 16.
How does an inverter compressor stay in step?
Picture pushing a child on a swing. Push at the right moment and the swing goes higher smoothly. Push at the wrong moment and you fight against it. An inverter drive works the same way with the compressor rotor. It switches current through the windings in a rotating sequence, and each switch must happen at the right point in the rotation.
To get that timing right, the board continuously estimates rotor position from voltages measured on the motor leads. Engineers often call this sensorless control, since no separate position sensor sits inside the compressor. The position circuit on the board does the measuring.
What can upset the position circuit?
Several faults can stop the board reading position correctly. Common causes include the following.
- A loose, burnt or corroded compressor lead or terminal.
- A compressor winding that has partly failed or become unbalanced.
- Damage to the position detection section of the outdoor board.
- Moisture or salt residue inside the outdoor electrical box.
- Surge damage after a storm.
- A compressor that is mechanically tight, so it starts unevenly.
- Very low supply voltage that distorts the signals at start up.
Connection problems and board faults come up most often. A failing compressor is less common but more serious.
When does code 16 usually appear?
Most often, 16 shows up as the compressor tries to start. Start up is the hardest moment for position detection, because the rotor moves slowly and the feedback signals are weak. If the board cannot lock onto the rotor position, the start fails. The board may try several times before giving up and flashing the code.
Some units show 16 during running instead, particularly when a connection works loose with vibration or heat. Either pattern helps the technician, so note when it happens.
How do you see code 16 on a Toshiba?
The indoor lamps normally flash quickly when the board stores a fault. With the wireless remote, press the recessed CHECK button using a pencil, then step through the codes until the indoor unit beeps. Our check codes guide gives the full steps.
Read the code before cutting the power, since removing power can wipe the stored fault.
What do you notice at the outdoor unit?
When code 16 strikes at start up, you may hear the outdoor unit click, hum briefly and then fall silent, sometimes several times in a row. The outdoor fan might spin up and then stop. Indoors, the fan keeps blowing for a while but the air never gets cold or warm.
If you notice these attempts, mention them. Repeated start attempts point strongly to a start up or position problem.
What should you try before calling?
A couple of steps are safe.
- Turn the unit off with the remote and leave it for at least ten minutes.
- Check the outdoor isolator and the breaker.
- Restart once and listen to how the outdoor unit behaves.
If 16 returns, leave the system off and book a technician. Do not open the outdoor unit, since the inverter holds high voltages even after you switch off the power.
Why does the inverter hold voltage after power off?
Inverter boards contain large capacitors that store energy. These capacitors can stay charged for some time after the power goes off. Technicians wait and then measure before touching anything inside. That is one reason why outdoor unit repairs must stay with trained, licensed people.
How does a technician diagnose code 16?
First, the technician confirms the code and listens to the start attempts. Next, with power isolated and capacitors safely discharged, they open the outdoor electrical box and inspect the compressor terminals, leads and board connectors for looseness, corrosion or heat damage.
Then they measure the compressor winding resistances, checking that all three windings match closely and that none leaks to earth. If the compressor tests well, they focus on the outdoor board, checking its output and the position detection circuit. In some cases, they also check refrigerant pressures to make sure the compressor is not trying to start against an unusual load.
What repairs fix code 16?
Depending on the findings, repairs may include the following.
- Tightening or replacing compressor terminals and leads.
- Cleaning and drying a damp electrical box, then sealing it.
- Replacing the outdoor control or inverter board.
- Correcting a supply voltage problem with help from an electrician.
- Replacing the compressor if winding tests confirm a fault.
Connection repairs often take little time and cost little. Board replacement costs more, and compressor replacement is a major job.
Why check the compressor terminals first?
The compressor terminals carry heavy current and sit on top of a component that vibrates and heats up every time it runs. Over years, terminal clips can loosen and oxidise. A poor connection distorts the feedback signals and can mimic a board fault.
Fixing a terminal costs little compared with a board, so a careful technician always checks connections before recommending parts. That approach saves you money when the fix turns out to be simple.
Can a failing compressor cause 16?
Yes, though less often. If a winding develops a partial short, the motor behaves unevenly and its feedback signals become unreliable. Similarly, a compressor with internal mechanical wear may resist turning at start up, which makes position detection harder.
When testing points to the compressor, the technician will explain the cost and whether repair makes sense for the age of your unit. Our installation page explains what to consider if replacement becomes the better option.
Does code 16 relate to other compressor codes?
Toshiba groups several compressor and drive codes close together. For instance, 14 covers inverter voltage and short circuit protection, 17 covers current detected while the compressor should be off and 1C covers the compressor drive circuit. Code 16 focuses specifically on position detection.
Because these codes share possible causes, a technician often checks the same group of parts. The code still tells them where to begin.
Can supply problems cause 16?
Low or unstable supply voltage makes start up harder, since the inverter has less voltage to work with as it pushes the rotor into motion. Weak feedback signals combined with low voltage can lead the board to lose track. If 16 appears mostly on hot afternoons when the network is under heavy load, the supply deserves a close look.
Does salt air affect the outdoor board?
Near the coast, salt carried on the breeze settles inside outdoor units over time. On circuit boards, salt residue attracts moisture and can create tiny leakage paths between tracks. Those paths can upset sensitive circuits such as position detection. Coastal homes therefore benefit from regular checks of the outdoor electrical box.
What happens if you keep restarting?
Each failed start sends current through the windings and the inverter without the compressor turning properly. Repeated attempts heat the parts and may worsen a marginal fault. So after one restart, leave the system off if 16 returns and book a technician.
Why is start up the hardest moment?
When the compressor sits still, the rotor produces no feedback at all. So the board must nudge it into motion using a set starting routine, then pick up the faint signals as the rotor begins to turn. At low speed, those signals are small and easily disturbed by electrical noise, poor connections or uneven windings.
Once the compressor reaches a moderate speed, the signals grow stronger and detection becomes easier. That is why many position faults appear only at start up and why a unit may run fine for hours once it gets going.
Can refrigerant problems make starting harder?
Yes. If high and low side pressures have not equalised before the compressor tries to start, it faces a heavier load at the very moment the board is trying to detect position. Normally, Toshiba units wait a few minutes after stopping before they restart, which gives pressures time to balance. However, an overcharged system or a restriction in the circuit can upset that balance.
So if the electrical tests look fine, the technician may check refrigerant pressures and the charge. Our gas regas page explains how a correct charge gets confirmed.
What about wifi modules and add on controllers?
Add on wifi modules connect to the indoor unit, not the outdoor board, so they do not affect compressor position detection. If your code 16 appeared around the time you added a wifi module, the timing is most likely a coincidence. Still, mention any recent changes, since the technician may want to rule them out.
How long does a code 16 repair take?
Terminal and lead repairs often finish in one visit. Board replacements depend on part availability and usually need the exact model and serial number. Compressor replacement involves refrigerant recovery, brazing, testing and recharging, so it takes the longest. The technician will give you a realistic timeline after diagnosis.
Is code 16 common on older Toshiba units?
Older units have had more years of vibration, heat and weather, so connection and board faults become more likely with age. Still, many older units run reliably for years after a simple terminal repair. The technician will look at the overall condition of the unit before recommending a path.
How can you reduce the risk of compressor faults?
Keep the outdoor unit clean and well ventilated so the compressor does not run hotter than it needs to. Fix refrigerant leaks promptly, since a low charge affects compressor cooling. Switch the system off during severe storms, and book regular servicing so a technician can check terminals and boards. Our service page explains what a service covers.
What details help when you book?
Tell us the code, whether it appears at start up or during running and how the outdoor unit sounds when it tries to start. Mention recent storms, rain or work near the outdoor unit. Also provide the model from the indoor unit label and, if you can, a photo of the outdoor unit data plate.
What does a code 16 repair cost?
The cost depends on what the testing finds. Terminal and lead fixes sit at the lower end, a board replacement sits in the middle and a compressor replacement sits at the top. The technician always explains the cause and gives you the price before starting. Our pricing page explains how we quote.
Who repairs Toshiba error code 16 in Sydney?
We repair Toshiba error code 16 faults across Sydney. To book, phone 02 9071 1142 or use our booking page. The technician will test the compressor connections, windings and outdoor board and explain the fix before starting.
For more Toshiba codes, browse our error code library.
Frequently asked questions
What does Toshiba error code 16 mean?
It means the outdoor board could not track the compressor rotor position, so it stopped the compressor.
When does code 16 usually appear?
Most often at compressor start up, when position detection is hardest.
Is code 16 a compressor failure?
Not always. Loose terminals and board faults are more common causes.
Can low voltage cause code 16?
Yes. Low or unstable supply makes start up harder and can upset position detection.
Should I keep restarting the unit?
No. After one restart, leave it off if 16 returns and book a technician.
How do I book?
Phone 02 9071 1142 with the code, model and how the outdoor unit behaves.